# Using Odrive S1 for an autonomous RC car

**URL:** <https://discourse.odriverobotics.com/t/using-odrive-s1-for-an-autonomous-rc-car/14308>\
**Category:** Projects\
**Created:** [June 24, 2026, 1:58pm UTC](https://discourse.odriverobotics.com/t/using-odrive-s1-for-an-autonomous-rc-car/14308 "2026-06-24T13:58:07Z")\
**Posts on this page:** 2\
**Page:** 1

<div class="post-metadata">

**Author:** ![LeobardoGF](https://discourse.odriverobotics.com/user_avatar/discourse.odriverobotics.com/leobardogf/32/8014_2.png) [@LeobardoGF](https://discourse.odriverobotics.com/u/LeobardoGF)\
**Post date:** [June 24, 2026, 1:58pm UTC](https://discourse.odriverobotics.com/t/using-odrive-s1-for-an-autonomous-rc-car/14308/1 "2026-06-24T13:58:07Z")

</div>

I’m trying to run an EZRUN 3652 SD G3 5400KV motor installed in a RC 1/10 chassis with ODrive and I’m consistently failing the calibration process.  
The motor has integrated hall sensors (A, B, C + thermistor), and they seem to work correctly. I can see the encoder values respond when rotating the motor by hand.  
However, I cannot complete calibration successfully.

**Hardware:**

- ODrive S1
- PSU: 24V, 12A current limit
- Motor: EZRUN 3652 SD G3 – 5400KV
- Motor type: HIGH\_CURRENT
- Encoder: Hall sensors (A, B, C + thermistor)
- Wiring: short cables, standard connections

**Configuration:**

odrv0.axis0.motor.config.motor\_type = MOTOR\_TYPE\_HIGH\_CURRENT  
odrv0.axis0.motor.config.pole\_pairs = 2  
odrv0.axis0.motor.config.current\_lim = 15  
odrv0.axis0.motor.config.calibration\_current = 22  
odrv0.axis0.motor.config.resistance\_calib\_max\_voltage = 4.5  
odrv0.axis0.controller.config.lockin\_current = 10

**Steps to reproduce**

Power on ODrive (24V supply)  
Run:  
odrv0.axis0.requested\_state = AXIS\_STATE\_FULL\_CALIBRATION\_SEQUENCE  
Calibration begins but does not complete  
Axis disarms and throws errors

**Errors:**  
Consistently getting:  
UNBALANCED\_PHASES  
DISARMED  
MISSING\_ESTIMATE

**What I’ve tried:**

Varying calibration current across a wide range  
Adjusting resistance calibration voltage  
Multiple calibration attempts  
Verified hall encoder is responding correctly

**Questions**

Are these errors caused by incorrect configuration, or is this motor inherently difficult to use with ODrive?  
Are there recommended settings for very high KV motors with hall sensors?  
Should I significantly reduce calibration current/voltage, or is the issue elsewhere?  
Is there a motor (KV range or specific models) you would recommend that works reliably with ODrive as a replacement?

---

<div class="post-metadata">

**Author:** ![solomondg](https://discourse.odriverobotics.com/letter_avatar_proxy/v4/letter/s/bcef8e/32.png) [@solomondg](https://discourse.odriverobotics.com/u/solomondg)\
**Post date:** [June 25, 2026, 2:55am UTC](https://discourse.odriverobotics.com/t/using-odrive-s1-for-an-autonomous-rc-car/14308/2 "2026-06-25T02:55:37Z")

</div>

Hi! Just to check – you said you’re using an S1, but those look like v3.6 style endpoints. Which ODrive are you using?
