|
PHASE_RESISTANCE_OUT_OF_RANGE for gimbal motor at 12v
|
|
3
|
514
|
July 14, 2025
|
|
Can I power Arduino from ODrive 3.6 board?
|
|
5
|
564
|
July 13, 2025
|
|
ODrive Mult-Turn Homing on Startup
|
|
3
|
671
|
July 11, 2025
|
|
Differences between odrivetool and ASCII protocol (Arduino)
|
|
2
|
430
|
July 7, 2025
|
|
Trouble getting ILM-E70x10 motor to work with ODrive S1
|
|
12
|
1053
|
June 26, 2025
|
|
Help Needed with Tuning ODrive for Precise Position Control on Custom BLDC Setup
|
|
1
|
1051
|
June 25, 2025
|
|
Z index and FOC reading
|
|
5
|
532
|
June 25, 2025
|
|
Odrive Arduino velocity
|
|
1
|
332
|
June 22, 2025
|
|
Negative current control when generator back EMF is below battery voltage
|
|
2
|
911
|
June 18, 2025
|
|
What happens to regenerative energy with no battery connected?
|
|
1
|
416
|
June 18, 2025
|
|
Help Needed: Motor Not Spinning Properly After Calibration (ODrive v3.6 + 5065 BLDC)
|
|
1
|
667
|
June 18, 2025
|
|
Using ODrive v3.6 for 1 Ton AGV with 4 x 1800W BLDC Motors – Looking for Advice
|
|
3
|
593
|
June 14, 2025
|
|
In Odrive S1 using Raspbian 5, if I give the active_error command, I don't get any error.
|
|
5
|
504
|
June 13, 2025
|
|
Torque Setpoint update rate through CAN (ODrive Micro)
|
|
1
|
511
|
June 12, 2025
|
|
2S Battery power for Micro?
|
|
4
|
458
|
June 11, 2025
|
|
Using negative values for torque control
|
|
5
|
566
|
June 11, 2025
|
|
How to test the max torque of motor
|
|
1
|
603
|
June 8, 2025
|
|
How to move the Hall sensor motor on Odrive 3.6
|
|
1
|
718
|
June 3, 2025
|
|
How do I copy the configuration of axis0 to aixs1?
|
|
1
|
491
|
June 3, 2025
|
|
2 stm32 communucation canbus
|
|
5
|
557
|
May 19, 2025
|
|
odrive.getState() == AXIS_STATE_UNDEFINED (UART)
|
|
10
|
775
|
May 13, 2025
|
|
Current rating configuration for motor controller and motor
|
|
12
|
1167
|
May 10, 2025
|
|
End of Travel Sensors
|
|
1
|
432
|
May 8, 2025
|
|
ODrive Pro + AksIM-2 BiSS-C encoder: no-response / not_calibrated
|
|
13
|
1724
|
May 7, 2025
|
|
Odrive dies spontaneously
|
|
5
|
2225
|
May 5, 2025
|
|
current_meas_period * pll_kp < 1.0f
|
|
1
|
440
|
May 5, 2025
|
|
Suggestion for a magnetic encoder
|
|
8
|
2447
|
May 1, 2025
|
|
ODrive V3.6 Not Detected via USB After Inactivity – STM32 Still Alive
|
|
1
|
507
|
April 26, 2025
|
|
AntiCogging for S1
|
|
10
|
1431
|
April 25, 2025
|
|
E-Stops and ODrive
|
|
2
|
785
|
April 23, 2025
|