|
No connect, now a brick
|
|
5
|
1889
|
September 13, 2021
|
|
Motor closed loop cannot operate normally
|
|
10
|
1252
|
September 13, 2021
|
|
A wired problem ,one odrive with one motor working smoothly,but with two is not
|
|
6
|
1727
|
September 13, 2021
|
|
Odrv0.axis0.config.enable_sensorless_mode Does not Exist?
|
|
10
|
2956
|
September 11, 2021
|
|
Calibration procedure not completing
|
|
6
|
4301
|
September 10, 2021
|
|
0.5.3. firmware with 0.5.2. backup-config
|
|
1
|
1031
|
September 8, 2021
|
|
Can Message : 0x001 "ODrive Heartbeat Message"
|
|
0
|
934
|
September 6, 2021
|
|
Can bus drivers - firmware -
|
|
0
|
685
|
September 6, 2021
|
|
No backend error
|
|
4
|
8047
|
September 4, 2021
|
|
Cannot flash Odrive3.5 with StLINK V2-1
|
|
9
|
6085
|
August 31, 2021
|
|
Unkown Error 0x00000004
|
|
5
|
2641
|
August 31, 2021
|
|
RuntimeError: An error occured. Device Status: (11, 10, 0, 0)
|
|
4
|
892
|
August 31, 2021
|
|
Input_pos goes to zero when entering to closed loop control
|
|
1
|
877
|
August 29, 2021
|
|
Compatibility with a stepper motor
|
|
4
|
3006
|
August 27, 2021
|
|
USB over-current error
|
|
1
|
1993
|
August 27, 2021
|
|
Bldc motor becomes weak over time
|
|
9
|
1906
|
August 27, 2021
|
|
Firmware update failed, no device found now
|
|
1
|
910
|
August 23, 2021
|
|
Cannot set torque_constant on new odrive
|
|
1
|
1274
|
August 22, 2021
|
|
Error using 2 motors: ERROR_MODULATION_IS_NAN
|
|
4
|
2780
|
August 21, 2021
|
|
Getting control loop values
|
|
1
|
765
|
August 17, 2021
|
|
Sensorless at high speed
|
|
4
|
2656
|
August 17, 2021
|
|
Failed to read serial_number using ASCII protocol
|
|
3
|
1179
|
August 17, 2021
|
|
ODrive not powering on
|
|
2
|
831
|
August 17, 2021
|
|
Using UART with ODrive
|
|
0
|
1570
|
August 16, 2021
|
|
Only one spi master use,
|
|
3
|
951
|
August 15, 2021
|
|
DFU Flashing Error
|
|
5
|
3536
|
August 15, 2021
|
|
DC_BUS_OVER_REGEN_CURRENT (Error)
|
|
1
|
4532
|
August 14, 2021
|
|
Endstop ghost-triggered by call to encoder.pos_estimate
|
|
3
|
865
|
August 12, 2021
|
|
Problem with save_configuration() using python
|
|
4
|
2939
|
August 12, 2021
|
|
Axis1 works inappropriately
|
|
0
|
838
|
August 10, 2021
|