|
About the Support category
|
|
0
|
2868
|
April 7, 2017
|
|
AS5047P encoder "EncoderError.CPR_POLEPAIRS_MISMATCH" error
|
|
27
|
6749
|
October 20, 2026
|
|
ODrive Pro reports 4.8–5.4 V for vbus_voltage despite measuring 24 V at DC+ and DC−
|
|
6
|
182
|
October 20, 2026
|
|
ODrive Micro + Renishaw EVOLUTE 26-bit BiSS-C: NO_RESPONSE
|
|
1
|
101
|
October 19, 2026
|
|
Motor Is Jittery During Encoder Phase Offset Calibration
|
|
8
|
227
|
October 18, 2026
|
|
ODrive Micro Multiple ADC Failures and VBUS Stuck at 26.4V
|
|
1
|
194
|
October 9, 2026
|
|
ODrive S1 Accessories Components
|
|
1
|
220
|
September 30, 2026
|
|
ODrive 3.6 56V Encoder Error 512 Calibration Failed
|
|
1
|
271
|
September 28, 2026
|
|
4 ODrive S1 fried ? T8-T31 8V
|
|
6
|
637
|
September 26, 2026
|
|
Asymmetrical ILLEGAL_HALL_STATE on Axis 0 only - Pinpointed to DC_calib_phC offset (v3.5 24V)
|
|
1
|
206
|
September 25, 2026
|
|
Iq from FOC during motor turning
|
|
1
|
237
|
September 17, 2026
|
|
Command ID 0x08 on CAN Bus
|
|
9
|
805
|
September 17, 2026
|
|
Odrive Can adapter not showing up in windows 11
|
|
14
|
755
|
September 4, 2026
|
|
Controlling ODrive S1 GPIOs via CAN
|
|
1
|
470
|
September 4, 2026
|
|
Sensorless pole slipping on ramp-up under propeller load — torque_constant sensitivity (T500, ODrive Pro 0.6.12)
|
|
3
|
488
|
September 3, 2026
|
|
Motor current creep to current_soft_max at constant velocity under load, sensorless T500 (ODrive Pro 0.6.12)
|
|
1
|
405
|
September 2, 2026
|
|
Low braking current
|
|
6
|
563
|
August 24, 2026
|
|
Unable to detect Odrive
|
|
2
|
1286
|
August 23, 2026
|
|
Odrive Pro Configurable Watchdog
|
|
1
|
332
|
August 21, 2026
|
|
SPI Encoder (BiSS-C) fails to initialize when DC power is applied first
|
|
3
|
748
|
August 19, 2026
|
|
Sudden motor current spike on deceleration or reversal, sensorless T500 (ODrive Pro 0.6.10)
|
|
1
|
356
|
August 17, 2026
|
|
DC bus / DC-link capacitance value for ODrive S1 (needed for external precharge design)
|
|
2
|
578
|
August 14, 2026
|
|
ODrive Regen Clamp maximum operating voltage
|
|
4
|
485
|
August 14, 2026
|
|
Heavy Chasis with botwheel and S1
|
|
1
|
554
|
August 13, 2026
|
|
Reading load encoder.raw over CAN?
|
|
1
|
347
|
August 5, 2026
|
|
ENCODER_INDEX_SEARCH spins indefinitely and never detects Z, but raw GPIO polling shows clean transitions
|
|
3
|
478
|
July 20, 2026
|
|
Odrive Pro CAN-bus shows error BUS_OFF
|
|
7
|
907
|
July 20, 2026
|
|
Torque limits over CAN
|
|
1
|
390
|
July 20, 2026
|
|
ODrive V3.6 Connection Issue
|
|
7
|
683
|
July 20, 2026
|
|
ODrive S1 Short Circuit – Burned Diode D8
|
|
4
|
429
|
July 9, 2026
|