|
About the ODrive Pro Support category
|
|
1
|
1145
|
July 24, 2025
|
|
Iq from FOC during motor turning
|
|
1
|
309
|
September 17, 2026
|
|
Sensorless handoff never produces real torque on low-inductance FPV motor (ODrive Pro, 0.6.6 & 0.6.11) — telemetry shows lock, motor is actually stalled
|
|
1
|
83
|
November 6, 2026
|
|
ODrive Pro reports 4.8–5.4 V for vbus_voltage despite measuring 24 V at DC+ and DC−
|
|
10
|
417
|
November 6, 2026
|
|
Sensorless pole slipping on ramp-up under propeller load — torque_constant sensitivity (T500, ODrive Pro 0.6.12)
|
|
3
|
611
|
September 3, 2026
|
|
Motor current creep to current_soft_max at constant velocity under load, sensorless T500 (ODrive Pro 0.6.12)
|
|
1
|
483
|
September 2, 2026
|
|
Odrive Pro Configurable Watchdog
|
|
1
|
392
|
August 21, 2026
|
|
SPI Encoder (BiSS-C) fails to initialize when DC power is applied first
|
|
3
|
821
|
August 19, 2026
|
|
Sudden motor current spike on deceleration or reversal, sensorless T500 (ODrive Pro 0.6.10)
|
|
1
|
417
|
August 17, 2026
|
|
Reading load encoder.raw over CAN?
|
|
1
|
399
|
August 5, 2026
|
|
Odrive Pro CAN-bus shows error BUS_OFF
|
|
7
|
1020
|
July 20, 2026
|
|
Torque limits over CAN
|
|
1
|
467
|
July 20, 2026
|
|
ODrive Pro - CAN Transmitting But Not Receiving
|
|
12
|
937
|
July 4, 2026
|
|
How to set Brake Resistor value on ODrive Pro?
|
|
11
|
5680
|
June 25, 2026
|
|
Brushless DC motor passing calibration, then hits velocity limit
|
|
5
|
829
|
May 8, 2026
|
|
Anticogging Missing Estimate Error with ODrive Pro, OA1 & M8325
|
|
1
|
684
|
April 23, 2026
|
|
Difficulty in Position Control
|
|
1
|
707
|
March 18, 2026
|
|
Motor Calibration Data in Config
|
|
3
|
1339
|
February 17, 2026
|
|
Odrive Pro CAN Trouble when connecting to BigTreeTech Manta M8P
|
|
5
|
794
|
February 17, 2026
|
|
CNC controller and Odrive
|
|
7
|
1616
|
January 6, 2026
|
|
Increase in vel_gain issue
|
|
9
|
1240
|
December 8, 2025
|
|
Odrive Pro Max rated Fan current
|
|
2
|
578
|
November 25, 2025
|
|
Too little torque at max current under torque control mode
|
|
7
|
2887
|
November 20, 2025
|
|
How to use ODrive Pro with AksIM-4 encoder with the SPI EncoLink protocol
|
|
1
|
592
|
November 16, 2025
|
|
Control velocity in filtered position control mode
|
|
1
|
797
|
November 10, 2025
|
|
EMI concerns with stacking odrives?
|
|
1
|
647
|
October 20, 2025
|
|
CAN-FD OdrivePro Tx good but Rx rejected
|
|
0
|
731
|
October 17, 2025
|
|
Weird outputs when running motor (vel_estimator problem?)
|
|
11
|
1472
|
October 7, 2025
|
|
CAN Communication Issue Between ODrive and USB-CAN — No Frames Visible in candump - No Messages Transmitted Despite Correct Setup
|
|
2
|
2310
|
October 1, 2025
|
|
ODrive Pro Fully Isolated CAN
|
|
3
|
2042
|
October 1, 2025
|