About the ODrive v3 Support category
|
|
1
|
268
|
October 25, 2023
|
Odrive v3.4-48V Update to Firmware v0.5.6
|
|
1
|
70
|
July 16, 2024
|
Unable to backup configuration
|
|
2
|
75
|
July 3, 2024
|
V3.6 56Volt loses output to M1
|
|
9
|
103
|
June 21, 2024
|
Odrive D5065 - 270KV Motor Torque Issue
|
|
6
|
173
|
May 31, 2024
|
BLDC smooth start and stop
|
|
12
|
220
|
May 30, 2024
|
ODrive V3.6 Encoder Position and Velocity == 0 over CAN until it's put in closed loop control
|
|
2
|
156
|
May 17, 2024
|
Getting started with ODrive V3.5
|
|
2
|
206
|
May 14, 2024
|
Abnormal behavior with the same parameters
|
|
9
|
137
|
April 30, 2024
|
Odrive control using PyQt joystick
|
|
0
|
199
|
April 25, 2024
|
AXIS_STATE_CLOSED_LOOP_CONTROL issue
|
|
12
|
272
|
April 24, 2024
|
After flashing ODrive3.6 the device is not detected
|
|
3
|
157
|
April 12, 2024
|
Motor is unstable at low RPM
|
|
36
|
511
|
April 11, 2024
|
Hall polarity calibration returns INVALID_STATE
|
|
4
|
177
|
April 10, 2024
|
Different phase_inductance values for two identical motors
|
|
5
|
173
|
March 31, 2024
|
Error of current_limit_violation
|
|
2
|
183
|
March 17, 2024
|
Cpr error with correct input
|
|
26
|
304
|
March 6, 2024
|
Get Current over CAN is always 0
|
|
2
|
165
|
February 29, 2024
|
Is this a way to measure torque?
|
|
15
|
292
|
February 20, 2024
|
Torque Limited Position Control
|
|
3
|
229
|
January 28, 2024
|
Increased current fried the board
|
|
0
|
213
|
January 26, 2024
|
PWM vel_Control
|
|
4
|
208
|
January 8, 2024
|
Can't perform homing at right position
|
|
1
|
181
|
December 26, 2023
|
Arduino ODrive and ARC
|
|
1
|
256
|
December 4, 2023
|
Does ODrive have an electronic brake function?
|
|
4
|
403
|
November 23, 2023
|
How to intentionally cause a Motor Error easily
|
|
5
|
304
|
November 21, 2023
|
Abnormal behavior of motor when physical load is applied to motor
|
|
3
|
236
|
November 16, 2023
|
Issue v3.6 56V vs v3.5 24V
|
|
3
|
274
|
November 16, 2023
|
No response on mode set
|
|
1
|
212
|
November 15, 2023
|
Sorry guys trying to update a 3.6 56v
|
|
9
|
632
|
November 2, 2023
|