|
Motor and encoder connection
|
|
1
|
1263
|
October 18, 2018
|
|
Is my odrive 24V or 48V?
|
|
5
|
1800
|
October 18, 2018
|
|
Newbie here, muscle support
|
|
0
|
833
|
October 17, 2018
|
|
Reading velocity and torque from hoverboard setup
|
|
5
|
5245
|
October 14, 2018
|
|
Current loop tuning and bandwith
|
|
1
|
1187
|
October 13, 2018
|
|
Change in Current Control Mode?
|
|
0
|
885
|
October 11, 2018
|
|
Excessive wobble from AMT10 Encoder
|
|
3
|
1811
|
October 11, 2018
|
|
Shipping/customs to EU
|
|
6
|
1188
|
October 10, 2018
|
|
Odrive 3.5 GERBER FILES/ALTIUM/BOM
|
|
2
|
5383
|
October 9, 2018
|
|
Axis error 0x01 when put into closed loop
|
|
3
|
2213
|
October 6, 2018
|
|
Minertia servo motor?
|
|
2
|
1063
|
October 5, 2018
|
|
ODrive PCB and Schematic files
|
|
0
|
2420
|
October 1, 2018
|
|
Pcb layout available to add differential encoders
|
|
2
|
2151
|
September 30, 2018
|
|
Read index_found via Arduino
|
|
2
|
960
|
September 30, 2018
|
|
External frequency reference
|
|
3
|
1211
|
September 30, 2018
|
|
Serial ascii protocol problem
|
|
1
|
1131
|
September 30, 2018
|
|
Odrive for a new project
|
|
1
|
895
|
September 30, 2018
|
|
Odrive inrush current
|
|
2
|
1118
|
September 27, 2018
|
|
Where are the trajectories?
|
|
15
|
8521
|
September 26, 2018
|
|
Is it possible to port oDrive firmware to VESC?
|
|
14
|
8093
|
September 30, 2018
|
|
What interface is best?
|
|
2
|
1880
|
September 23, 2018
|
|
Spacing the two banks of encoder input pins
|
|
6
|
1313
|
September 21, 2018
|
|
Synchronizing both motors
|
|
19
|
5069
|
September 21, 2018
|
|
Encoder index not found
|
|
1
|
1739
|
September 19, 2018
|
|
Maxon 272763 Motor
|
|
10
|
5109
|
September 16, 2018
|
|
Compiling Firmware and Make Help
|
|
7
|
3228
|
September 14, 2018
|
|
Understanding Ramp_up and spin_up parameters
|
|
1
|
869
|
September 10, 2018
|
|
Multiple ODrives on one serial port
|
|
3
|
1766
|
September 10, 2018
|
|
Is it "Peak" or "Constant" Torque
|
|
7
|
3058
|
September 3, 2018
|
|
Linear motor supported?
|
|
4
|
2072
|
September 2, 2018
|