|
Avoiding FULL_CALIBRATION_SEQUENCE
|
|
1
|
1388
|
September 16, 2021
|
|
Hall Polarity Calibration Illegal Hall State
|
|
1
|
1386
|
September 15, 2021
|
|
Every time need calibration of ODrive when I reboot or restart the Odrive
|
|
5
|
2535
|
September 15, 2021
|
|
Odrive not working anymore (5V regulator issue)
|
|
2
|
1055
|
September 15, 2021
|
|
Odrive does not execute position or velocity commands
|
|
4
|
1921
|
September 14, 2021
|
|
No connect, now a brick
|
|
5
|
1531
|
September 13, 2021
|
|
Motor closed loop cannot operate normally
|
|
10
|
992
|
September 13, 2021
|
|
A wired problem ,one odrive with one motor working smoothly,but with two is not
|
|
6
|
1484
|
September 13, 2021
|
|
Odrv0.axis0.config.enable_sensorless_mode Does not Exist?
|
|
10
|
2439
|
September 11, 2021
|
|
Calibration procedure not completing
|
|
6
|
3405
|
September 10, 2021
|
|
0.5.3. firmware with 0.5.2. backup-config
|
|
1
|
844
|
September 8, 2021
|
|
Can Message : 0x001 "ODrive Heartbeat Message"
|
|
0
|
793
|
September 6, 2021
|
|
Can bus drivers - firmware -
|
|
0
|
537
|
September 6, 2021
|
|
No backend error
|
|
4
|
6422
|
September 4, 2021
|
|
Cannot flash Odrive3.5 with StLINK V2-1
|
|
9
|
5386
|
August 31, 2021
|
|
Unkown Error 0x00000004
|
|
5
|
2174
|
August 31, 2021
|
|
RuntimeError: An error occured. Device Status: (11, 10, 0, 0)
|
|
4
|
745
|
August 31, 2021
|
|
Input_pos goes to zero when entering to closed loop control
|
|
1
|
723
|
August 29, 2021
|
|
Compatibility with a stepper motor
|
|
4
|
2416
|
August 27, 2021
|
|
USB over-current error
|
|
1
|
1724
|
August 27, 2021
|
|
Bldc motor becomes weak over time
|
|
9
|
1488
|
August 27, 2021
|
|
Unable to detect Odrive
|
|
1
|
899
|
August 26, 2021
|
|
Firmware update failed, no device found now
|
|
1
|
765
|
August 23, 2021
|
|
Cannot set torque_constant on new odrive
|
|
1
|
1071
|
August 22, 2021
|
|
Error using 2 motors: ERROR_MODULATION_IS_NAN
|
|
4
|
2445
|
August 21, 2021
|
|
Getting control loop values
|
|
1
|
605
|
August 17, 2021
|
|
Sensorless at high speed
|
|
4
|
2136
|
August 17, 2021
|
|
Failed to read serial_number using ASCII protocol
|
|
3
|
967
|
August 17, 2021
|
|
ODrive not powering on
|
|
2
|
664
|
August 17, 2021
|
|
Using UART with ODrive
|
|
0
|
1379
|
August 16, 2021
|