|
Position Hold torque
|
|
7
|
1058
|
July 19, 2025
|
|
Unclear what SetVelocity does (ODrive 3.6)
|
|
3
|
357
|
July 18, 2025
|
|
Cannot set control mode from Arduino (ODrive 3.6)
|
|
2
|
324
|
July 16, 2025
|
|
Hold position with torque control (ODdrive 3.6)
|
|
1
|
304
|
July 15, 2025
|
|
Different currents for motors in ODrive 3.6
|
|
1
|
283
|
July 15, 2025
|
|
USB-CAN Adapter Trouble
|
|
10
|
978
|
July 15, 2025
|
|
Odrive micro not moving to requested position
|
|
2
|
290
|
July 14, 2025
|
|
Controlling Two Motors with one PWM Channel
|
|
5
|
399
|
July 14, 2025
|
|
PHASE_RESISTANCE_OUT_OF_RANGE for gimbal motor at 12v
|
|
3
|
343
|
July 14, 2025
|
|
Can I power Arduino from ODrive 3.6 board?
|
|
5
|
432
|
July 13, 2025
|
|
ODrive Mult-Turn Homing on Startup
|
|
3
|
416
|
July 11, 2025
|
|
Differences between odrivetool and ASCII protocol (Arduino)
|
|
2
|
314
|
July 7, 2025
|
|
Trouble getting ILM-E70x10 motor to work with ODrive S1
|
|
12
|
753
|
June 26, 2025
|
|
Help Needed with Tuning ODrive for Precise Position Control on Custom BLDC Setup
|
|
1
|
697
|
June 25, 2025
|
|
Z index and FOC reading
|
|
5
|
378
|
June 25, 2025
|
|
Odrive Arduino velocity
|
|
1
|
249
|
June 22, 2025
|
|
Negative current control when generator back EMF is below battery voltage
|
|
2
|
525
|
June 18, 2025
|
|
What happens to regenerative energy with no battery connected?
|
|
1
|
325
|
June 18, 2025
|
|
Help Needed: Motor Not Spinning Properly After Calibration (ODrive v3.6 + 5065 BLDC)
|
|
1
|
426
|
June 18, 2025
|
|
Using ODrive v3.6 for 1 Ton AGV with 4 x 1800W BLDC Motors – Looking for Advice
|
|
3
|
458
|
June 14, 2025
|
|
In Odrive S1 using Raspbian 5, if I give the active_error command, I don't get any error.
|
|
5
|
394
|
June 13, 2025
|
|
Torque Setpoint update rate through CAN (ODrive Micro)
|
|
1
|
375
|
June 12, 2025
|
|
2S Battery power for Micro?
|
|
4
|
329
|
June 11, 2025
|
|
Using negative values for torque control
|
|
5
|
399
|
June 11, 2025
|
|
How to test the max torque of motor
|
|
1
|
429
|
June 8, 2025
|
|
How to move the Hall sensor motor on Odrive 3.6
|
|
1
|
506
|
June 3, 2025
|
|
How do I copy the configuration of axis0 to aixs1?
|
|
1
|
408
|
June 3, 2025
|
|
2 stm32 communucation canbus
|
|
5
|
450
|
May 19, 2025
|
|
odrive.getState() == AXIS_STATE_UNDEFINED (UART)
|
|
10
|
569
|
May 13, 2025
|
|
Current rating configuration for motor controller and motor
|
|
12
|
751
|
May 10, 2025
|