|
RuntimeError: An error occured. Device Status: (11, 10, 0, 0)
|
|
4
|
880
|
August 31, 2021
|
|
Hall efect sensor does not work
|
|
2
|
972
|
August 30, 2021
|
|
Input_pos goes to zero when entering to closed loop control
|
|
1
|
865
|
August 29, 2021
|
|
Compatibility with a stepper motor
|
|
4
|
2977
|
August 27, 2021
|
|
USB over-current error
|
|
1
|
1975
|
August 27, 2021
|
|
Error on controller.input_vel = 0
|
|
13
|
3507
|
August 27, 2021
|
|
Bldc motor becomes weak over time
|
|
9
|
1871
|
August 27, 2021
|
|
Contact odrive email/phone#
|
|
1
|
942
|
August 26, 2021
|
|
How can i clamp current_cmd to avoid current_limit_violation
|
|
1
|
1115
|
August 25, 2021
|
|
Gpio mode problem
|
|
6
|
1953
|
August 24, 2021
|
|
Torque when using Arudino with Hoverboard motor
|
|
1
|
1144
|
August 24, 2021
|
|
Firmware update failed, no device found now
|
|
1
|
898
|
August 23, 2021
|
|
Hoverboard motors calibrated fine but now error after turning once
|
|
4
|
1700
|
August 22, 2021
|
|
Implementation of sound feature
|
|
4
|
1801
|
August 22, 2021
|
|
Cannot set torque_constant on new odrive
|
|
1
|
1258
|
August 22, 2021
|
|
Error using 2 motors: ERROR_MODULATION_IS_NAN
|
|
4
|
2763
|
August 21, 2021
|
|
Current control on sensorless mode
|
|
2
|
1489
|
August 18, 2021
|
|
Getting control loop values
|
|
1
|
750
|
August 17, 2021
|
|
Sensorless at high speed
|
|
4
|
2630
|
August 17, 2021
|
|
Failed to read serial_number using ASCII protocol
|
|
3
|
1162
|
August 17, 2021
|
|
ODrive not powering on
|
|
2
|
819
|
August 17, 2021
|
|
Axis_error_motor_failed - FIXED
|
|
8
|
6965
|
August 16, 2021
|
|
What are the High-level source current and the Low-level sink current of GPIO?
|
|
0
|
798
|
August 16, 2021
|
|
Using UART with ODrive
|
|
0
|
1553
|
August 16, 2021
|
|
What are appropriate motor current_lim values?
|
|
9
|
3242
|
August 15, 2021
|
|
Only one spi master use,
|
|
3
|
935
|
August 15, 2021
|
|
DFU Flashing Error
|
|
5
|
3489
|
August 15, 2021
|
|
Hoverboard Motor | Speed Variation
|
|
0
|
999
|
August 14, 2021
|
|
DC_BUS_OVER_REGEN_CURRENT (Error)
|
|
1
|
4512
|
August 14, 2021
|
|
I am getting an unknown error code on motor calibration
|
|
1
|
1084
|
August 13, 2021
|