|
Using a CAN bus analyser to communicate with ODrive
|
|
4
|
3001
|
September 15, 2020
|
|
Is my encoder dead?
|
|
1
|
1080
|
September 13, 2020
|
|
ERROR_CURRENT_UNSTABLE in closed loop position control
|
|
15
|
2292
|
September 11, 2020
|
|
Geared motors with Hall and encoders not spinning in encoder mode
|
|
28
|
6364
|
September 10, 2020
|
|
Axis state stuck at undefined
|
|
7
|
2819
|
September 10, 2020
|
|
Odrive ERROR_CURRENT_UNSTABLE
|
|
22
|
6025
|
September 9, 2020
|
|
Failed full calibration with AMT232B-V absolute encoder
|
|
7
|
1662
|
September 9, 2020
|
|
ODrive 56V V.3.6 Fried
|
|
1
|
2215
|
September 7, 2020
|
|
V3.6docs available on Github?
|
|
1
|
1032
|
September 5, 2020
|
|
Some advices for trajectory mode
|
|
2
|
1604
|
August 31, 2020
|
|
Odrive control loop non-linearity
|
|
12
|
1490
|
August 29, 2020
|
|
Get steps taken in ENCODER_INDEX_SEARCH
|
|
2
|
829
|
August 25, 2020
|
|
ERROR_MODULATION_MAGNITUDE when doing index_search
|
|
12
|
4736
|
August 24, 2020
|
|
Odrive + MicroROS with ROS2 command
|
|
1
|
1959
|
August 24, 2020
|
|
Motor + odrive will not turn
|
|
11
|
3405
|
August 22, 2020
|
|
Odrive usb no longer showing up
|
|
4
|
2046
|
August 20, 2020
|
|
Encoder communication protocol
|
|
4
|
2275
|
August 20, 2020
|
|
Cannot connect to board with odrivetool after power outage
|
|
3
|
943
|
August 19, 2020
|
|
Cpr out of range error with ODrive 3.4 + ABI Magnetic Rotary Position Sensor (AS5047P)
|
|
9
|
5853
|
August 15, 2020
|
|
Odrive and Arduino USB Serial interface (Tx0,Rx0)
|
|
1
|
1934
|
August 15, 2020
|
|
Sensorless + Halls: Combined mode?
|
|
5
|
1225
|
August 14, 2020
|
|
UART mode ASCII Protocol maximum requests and response
|
|
2
|
1819
|
August 14, 2020
|
|
ERROR_CURRENT_UNSTABLE in CTRL_MODE_CURRENT_CONTROL
|
|
9
|
1686
|
August 14, 2020
|
|
Dead Board V3.6
|
|
5
|
1258
|
August 13, 2020
|
|
ODrive Allow Motor Slow Down To A Stop
|
|
1
|
1091
|
August 13, 2020
|
|
Current control bandwidth
|
|
7
|
13330
|
August 12, 2020
|
|
USB Comm Trouble: 56V V3.6
|
|
9
|
2840
|
August 11, 2020
|
|
DFU Update and Setup issues
|
|
4
|
1141
|
August 10, 2020
|
|
Gimbal engine configuration
|
|
1
|
1011
|
August 8, 2020
|
|
Improving the precision of current control output for torque control
|
|
3
|
2975
|
August 8, 2020
|