|
Input_pos goes to zero when entering to closed loop control
|
|
1
|
818
|
August 29, 2021
|
|
Compatibility with a stepper motor
|
|
4
|
2703
|
August 27, 2021
|
|
USB over-current error
|
|
1
|
1899
|
August 27, 2021
|
|
Error on controller.input_vel = 0
|
|
13
|
3315
|
August 27, 2021
|
|
Bldc motor becomes weak over time
|
|
9
|
1738
|
August 27, 2021
|
|
Unable to detect Odrive
|
|
1
|
1002
|
August 26, 2021
|
|
Contact odrive email/phone#
|
|
1
|
882
|
August 26, 2021
|
|
How can i clamp current_cmd to avoid current_limit_violation
|
|
1
|
1048
|
August 25, 2021
|
|
Gpio mode problem
|
|
6
|
1868
|
August 24, 2021
|
|
Torque when using Arudino with Hoverboard motor
|
|
1
|
1091
|
August 24, 2021
|
|
Firmware update failed, no device found now
|
|
1
|
850
|
August 23, 2021
|
|
Hoverboard motors calibrated fine but now error after turning once
|
|
4
|
1602
|
August 22, 2021
|
|
Implementation of sound feature
|
|
4
|
1725
|
August 22, 2021
|
|
Cannot set torque_constant on new odrive
|
|
1
|
1195
|
August 22, 2021
|
|
Error using 2 motors: ERROR_MODULATION_IS_NAN
|
|
4
|
2677
|
August 21, 2021
|
|
Current control on sensorless mode
|
|
2
|
1428
|
August 18, 2021
|
|
Getting control loop values
|
|
1
|
706
|
August 17, 2021
|
|
Sensorless at high speed
|
|
4
|
2450
|
August 17, 2021
|
|
Failed to read serial_number using ASCII protocol
|
|
3
|
1099
|
August 17, 2021
|
|
ODrive not powering on
|
|
2
|
766
|
August 17, 2021
|
|
Axis_error_motor_failed - FIXED
|
|
8
|
6767
|
August 16, 2021
|
|
What are the High-level source current and the Low-level sink current of GPIO?
|
|
0
|
744
|
August 16, 2021
|
|
Using UART with ODrive
|
|
0
|
1503
|
August 16, 2021
|
|
What are appropriate motor current_lim values?
|
|
9
|
3089
|
August 15, 2021
|
|
Only one spi master use,
|
|
3
|
878
|
August 15, 2021
|
|
DFU Flashing Error
|
|
5
|
3401
|
August 15, 2021
|
|
Hoverboard Motor | Speed Variation
|
|
0
|
958
|
August 14, 2021
|
|
DC_BUS_OVER_REGEN_CURRENT (Error)
|
|
1
|
4381
|
August 14, 2021
|
|
I am getting an unknown error code on motor calibration
|
|
1
|
1035
|
August 13, 2021
|
|
Endstop ghost-triggered by call to encoder.pos_estimate
|
|
3
|
798
|
August 12, 2021
|