|
Odrive controller for 3kW hub motor
|
|
1
|
509
|
July 7, 2025
|
|
ODrive V3 GUI (executable)
|
|
0
|
626
|
July 4, 2025
|
|
NO_RESPONSE error with AS5048A encoder
|
|
12
|
1734
|
July 3, 2025
|
|
I've made an offline web GUI for v0.5.6! :)
|
|
0
|
1414
|
June 29, 2025
|
|
PST-360 SPI Encoder Compatibility with ODrive Pro (v0.6.8 or later)
|
|
2
|
512
|
June 27, 2025
|
|
Trouble getting ILM-E70x10 motor to work with ODrive S1
|
|
12
|
877
|
June 26, 2025
|
|
Help Needed with Tuning ODrive for Precise Position Control on Custom BLDC Setup
|
|
1
|
825
|
June 25, 2025
|
|
Z index and FOC reading
|
|
5
|
423
|
June 25, 2025
|
|
CAN Bus; expanding to multi-node
|
|
1
|
688
|
June 24, 2025
|
|
Odrive Arduino velocity
|
|
1
|
275
|
June 22, 2025
|
|
Can the ODrive (56V) burn out if it is unpowered, but the motor is moved?
|
|
5
|
788
|
June 19, 2025
|
|
Negative current control when generator back EMF is below battery voltage
|
|
2
|
635
|
June 18, 2025
|
|
What happens to regenerative energy with no battery connected?
|
|
1
|
360
|
June 18, 2025
|
|
Help Needed: Motor Not Spinning Properly After Calibration (ODrive v3.6 + 5065 BLDC)
|
|
1
|
495
|
June 18, 2025
|
|
“Illegal Hall State” Error on M0 Despite Valid Hall Signals
|
|
1
|
780
|
June 17, 2025
|
|
oDrive v.36 No power LED, chips get hot immediately after plug in
|
|
2
|
858
|
June 15, 2025
|
|
Using ODrive v3.6 for 1 Ton AGV with 4 x 1800W BLDC Motors – Looking for Advice
|
|
3
|
512
|
June 14, 2025
|
|
In Odrive S1 using Raspbian 5, if I give the active_error command, I don't get any error.
|
|
5
|
439
|
June 13, 2025
|
|
Torque Setpoint update rate through CAN (ODrive Micro)
|
|
1
|
446
|
June 12, 2025
|
|
2S Battery power for Micro?
|
|
4
|
385
|
June 11, 2025
|
|
Using negative values for torque control
|
|
5
|
465
|
June 11, 2025
|
|
DC_BUS_OVER_VOLTAGE error triggers
|
|
33
|
4250
|
June 9, 2025
|
|
How to test the max torque of motor
|
|
1
|
496
|
June 8, 2025
|
|
AMT24 Series Encoders
|
|
3
|
815
|
June 6, 2025
|
|
Use of AMT112Q Encoder
|
|
1
|
349
|
June 4, 2025
|
|
How to move the Hall sensor motor on Odrive 3.6
|
|
1
|
563
|
June 3, 2025
|
|
How do I copy the configuration of axis0 to aixs1?
|
|
1
|
446
|
June 3, 2025
|
|
Thermal pad placement for fan heat sink?
|
|
4
|
787
|
June 3, 2025
|
|
Odrive 3.6 Hoverboard Motor Calibration
|
|
4
|
861
|
May 30, 2025
|
|
UNBALANCED_PHASES
|
|
1
|
457
|
May 30, 2025
|