|
Odrive micro not moving to requested position
|
|
2
|
584
|
July 14, 2025
|
|
Controlling Two Motors with one PWM Channel
|
|
5
|
861
|
July 14, 2025
|
|
PHASE_RESISTANCE_OUT_OF_RANGE for gimbal motor at 12v
|
|
3
|
840
|
July 14, 2025
|
|
Can I power Arduino from ODrive 3.6 board?
|
|
5
|
769
|
July 13, 2025
|
|
New to ODrive – Raspberry Pi Pico + Endstops + UART – is my config safe?
|
|
1
|
997
|
July 11, 2025
|
|
ODrive Mult-Turn Homing on Startup
|
|
3
|
1121
|
July 11, 2025
|
|
Check Errors in Arduino
|
|
5
|
922
|
July 8, 2025
|
|
Positioning Heatsink and Fan on Odrive Pro
|
|
12
|
1402
|
July 8, 2025
|
|
Encoder error ERROR_ILLEGAL_HALL_STATE
|
|
52
|
40145
|
July 8, 2025
|
|
Effectiveness of dc_bus_current_report_filter_k for Low-Rate Sampling on ODrive Pro
|
|
3
|
638
|
July 7, 2025
|
|
Controlling ODrive with STM32 board and Matlab
|
|
5
|
3903
|
July 7, 2025
|
|
Differences between odrivetool and ASCII protocol (Arduino)
|
|
2
|
605
|
July 7, 2025
|
|
Odrive controller for 3kW hub motor
|
|
1
|
840
|
July 7, 2025
|
|
ODrive V3 GUI (executable)
|
|
0
|
1086
|
July 4, 2025
|
|
NO_RESPONSE error with AS5048A encoder
|
|
12
|
2738
|
July 3, 2025
|
|
I've made an offline web GUI for v0.5.6! :)
|
|
0
|
2575
|
June 29, 2025
|
|
PST-360 SPI Encoder Compatibility with ODrive Pro (v0.6.8 or later)
|
|
2
|
848
|
June 27, 2025
|
|
Trouble getting ILM-E70x10 motor to work with ODrive S1
|
|
12
|
1538
|
June 26, 2025
|
|
Help Needed with Tuning ODrive for Precise Position Control on Custom BLDC Setup
|
|
1
|
1576
|
June 25, 2025
|
|
Z index and FOC reading
|
|
5
|
763
|
June 25, 2025
|
|
CAN Bus; expanding to multi-node
|
|
1
|
1079
|
June 24, 2025
|
|
Odrive Arduino velocity
|
|
1
|
488
|
June 22, 2025
|
|
Can the ODrive (56V) burn out if it is unpowered, but the motor is moved?
|
|
5
|
1457
|
June 19, 2025
|
|
Negative current control when generator back EMF is below battery voltage
|
|
2
|
1496
|
June 18, 2025
|
|
What happens to regenerative energy with no battery connected?
|
|
1
|
584
|
June 18, 2025
|
|
Help Needed: Motor Not Spinning Properly After Calibration (ODrive v3.6 + 5065 BLDC)
|
|
1
|
1097
|
June 18, 2025
|
|
“Illegal Hall State” Error on M0 Despite Valid Hall Signals
|
|
1
|
1463
|
June 17, 2025
|
|
oDrive v.36 No power LED, chips get hot immediately after plug in
|
|
2
|
1138
|
June 15, 2025
|
|
Using ODrive v3.6 for 1 Ton AGV with 4 x 1800W BLDC Motors – Looking for Advice
|
|
3
|
835
|
June 14, 2025
|
|
In Odrive S1 using Raspbian 5, if I give the active_error command, I don't get any error.
|
|
5
|
691
|
June 13, 2025
|