|
Encoder error ERROR_ILLEGAL_HALL_STATE
|
|
52
|
32445
|
July 8, 2025
|
|
Effectiveness of dc_bus_current_report_filter_k for Low-Rate Sampling on ODrive Pro
|
|
3
|
300
|
July 7, 2025
|
|
Controlling ODrive with STM32 board and Matlab
|
|
5
|
1597
|
July 7, 2025
|
|
Differences between odrivetool and ASCII protocol (Arduino)
|
|
2
|
265
|
July 7, 2025
|
|
Odrive controller for 3kW hub motor
|
|
1
|
395
|
July 7, 2025
|
|
ODrive V3 GUI (executable)
|
|
0
|
412
|
July 4, 2025
|
|
NO_RESPONSE error with AS5048A encoder
|
|
12
|
1250
|
July 3, 2025
|
|
I've made an offline web GUI for v0.5.6! :)
|
|
0
|
972
|
June 29, 2025
|
|
PST-360 SPI Encoder Compatibility with ODrive Pro (v0.6.8 or later)
|
|
2
|
379
|
June 27, 2025
|
|
Trouble getting ILM-E70x10 motor to work with ODrive S1
|
|
12
|
605
|
June 26, 2025
|
|
Help Needed with Tuning ODrive for Precise Position Control on Custom BLDC Setup
|
|
1
|
532
|
June 25, 2025
|
|
Z index and FOC reading
|
|
5
|
296
|
June 25, 2025
|
|
CAN Bus; expanding to multi-node
|
|
1
|
526
|
June 24, 2025
|
|
Odrive Arduino velocity
|
|
1
|
205
|
June 22, 2025
|
|
Can the ODrive (56V) burn out if it is unpowered, but the motor is moved?
|
|
5
|
552
|
June 19, 2025
|
|
Negative current control when generator back EMF is below battery voltage
|
|
2
|
356
|
June 18, 2025
|
|
What happens to regenerative energy with no battery connected?
|
|
1
|
270
|
June 18, 2025
|
|
Help Needed: Motor Not Spinning Properly After Calibration (ODrive v3.6 + 5065 BLDC)
|
|
1
|
325
|
June 18, 2025
|
|
“Illegal Hall State” Error on M0 Despite Valid Hall Signals
|
|
1
|
541
|
June 17, 2025
|
|
oDrive v.36 No power LED, chips get hot immediately after plug in
|
|
2
|
757
|
June 15, 2025
|
|
Using ODrive v3.6 for 1 Ton AGV with 4 x 1800W BLDC Motors – Looking for Advice
|
|
3
|
395
|
June 14, 2025
|
|
In Odrive S1 using Raspbian 5, if I give the active_error command, I don't get any error.
|
|
5
|
339
|
June 13, 2025
|
|
Torque Setpoint update rate through CAN (ODrive Micro)
|
|
1
|
292
|
June 12, 2025
|
|
2S Battery power for Micro?
|
|
4
|
274
|
June 11, 2025
|
|
Using negative values for torque control
|
|
5
|
307
|
June 11, 2025
|
|
DC_BUS_OVER_VOLTAGE error triggers
|
|
33
|
3288
|
June 9, 2025
|
|
How to test the max torque of motor
|
|
1
|
357
|
June 8, 2025
|
|
AMT24 Series Encoders
|
|
3
|
623
|
June 6, 2025
|
|
Use of AMT112Q Encoder
|
|
1
|
268
|
June 4, 2025
|
|
How to move the Hall sensor motor on Odrive 3.6
|
|
1
|
413
|
June 3, 2025
|