|
Flush the velocity PID loop to prevent unwanted yaw correction
|
|
1
|
637
|
September 4, 2021
|
|
Firmware 0.5.2 Release Thread
|
|
62
|
15094
|
September 2, 2021
|
|
Firmware upgrade to 0.5.2usb disappear, brush 0.5.1 firmware completely normal, solve the problem
|
|
17
|
2894
|
September 1, 2021
|
|
Cannot flash Odrive3.5 with StLINK V2-1
|
|
9
|
5679
|
August 31, 2021
|
|
Unkown Error 0x00000004
|
|
5
|
2416
|
August 31, 2021
|
|
RuntimeError: An error occured. Device Status: (11, 10, 0, 0)
|
|
4
|
803
|
August 31, 2021
|
|
Hall efect sensor does not work
|
|
2
|
890
|
August 30, 2021
|
|
Input_pos goes to zero when entering to closed loop control
|
|
1
|
782
|
August 29, 2021
|
|
Compatibility with a stepper motor
|
|
4
|
2598
|
August 27, 2021
|
|
USB over-current error
|
|
1
|
1850
|
August 27, 2021
|
|
Error on controller.input_vel = 0
|
|
13
|
3169
|
August 27, 2021
|
|
Bldc motor becomes weak over time
|
|
9
|
1658
|
August 27, 2021
|
|
Unable to detect Odrive
|
|
1
|
962
|
August 26, 2021
|
|
Contact odrive email/phone#
|
|
1
|
828
|
August 26, 2021
|
|
How can i clamp current_cmd to avoid current_limit_violation
|
|
1
|
991
|
August 25, 2021
|
|
Gpio mode problem
|
|
6
|
1811
|
August 24, 2021
|
|
Torque when using Arudino with Hoverboard motor
|
|
1
|
1064
|
August 24, 2021
|
|
Firmware update failed, no device found now
|
|
1
|
825
|
August 23, 2021
|
|
Hoverboard motors calibrated fine but now error after turning once
|
|
4
|
1499
|
August 22, 2021
|
|
Implementation of sound feature
|
|
4
|
1656
|
August 22, 2021
|
|
Cannot set torque_constant on new odrive
|
|
1
|
1151
|
August 22, 2021
|
|
Error using 2 motors: ERROR_MODULATION_IS_NAN
|
|
4
|
2607
|
August 21, 2021
|
|
Current control on sensorless mode
|
|
2
|
1386
|
August 18, 2021
|
|
Getting control loop values
|
|
1
|
676
|
August 17, 2021
|
|
Sensorless at high speed
|
|
4
|
2312
|
August 17, 2021
|
|
Failed to read serial_number using ASCII protocol
|
|
3
|
1061
|
August 17, 2021
|
|
ODrive not powering on
|
|
2
|
727
|
August 17, 2021
|
|
Axis_error_motor_failed - FIXED
|
|
8
|
6627
|
August 16, 2021
|
|
What are the High-level source current and the Low-level sink current of GPIO?
|
|
0
|
671
|
August 16, 2021
|
|
Using UART with ODrive
|
|
0
|
1461
|
August 16, 2021
|