|
Phase inductance out of range after changing shunts
|
|
2
|
1224
|
December 23, 2021
|
|
Motor not turning after closed loop state
|
|
3
|
1058
|
December 22, 2021
|
|
ODrive USB connections
|
|
4
|
899
|
December 21, 2021
|
|
Arduino stops receiving GetPosition data after a few seconds
|
|
11
|
1739
|
December 17, 2021
|
|
Tuning a D6374 to the limits
|
|
3
|
1107
|
December 15, 2021
|
|
Mechanical Brake control through arduino
|
|
3
|
1551
|
December 15, 2021
|
|
Control 24V BLDC MOTOR (Brake, Encoder)
|
|
16
|
4854
|
December 13, 2021
|
|
[LEGACY_PROTOCOL] previous endpoint operation still not sent
|
|
1
|
1581
|
December 12, 2021
|
|
Is my ODrive Fried?
|
|
1
|
890
|
December 11, 2021
|
|
Tuning hoverboard motors
|
|
6
|
4080
|
December 6, 2021
|
|
MOTOR_ERROR_DRV_FAULT v3.6b
|
|
1
|
990
|
October 22, 2021
|
|
Sending Commands from Arduino and receiving encoder data
|
|
7
|
5537
|
December 1, 2021
|
|
ODrive 24V with BLDC+Hall Encoder Does not work
|
|
2
|
1219
|
December 1, 2021
|
|
Problem calibrating hoverboard motor
|
|
8
|
3595
|
December 1, 2021
|
|
How to get the velocity of BLDC in real time
|
|
1
|
798
|
December 1, 2021
|
|
ODRIVE V3.6 for SinCos Encoder
|
|
2
|
924
|
November 30, 2021
|
|
No torque in torque mode
|
|
51
|
10738
|
November 30, 2021
|
|
Motor doesn't rotate during ENCODER_INDEX_SEARCH
|
|
2
|
917
|
November 30, 2021
|
|
ODrive not working in certain motors?
|
|
18
|
4783
|
November 30, 2021
|
|
Scooter (G30 Max) Motor Not Spinning After Hall Pre-Calibration
|
|
1
|
747
|
November 30, 2021
|
|
Motor fails to rotate in both directions when start up and shows "AXIS ERROR ENCODER FAILED" and "ENCODER ERROR INDEX NOT FOUND YET" error
|
|
5
|
3366
|
November 29, 2021
|
|
Infinite inductance on only one channel?
|
|
3
|
698
|
November 27, 2021
|
|
Odrive not showing on USB
|
|
5
|
1297
|
November 25, 2021
|
|
Linear encoder 15Mhz
|
|
12
|
1466
|
November 25, 2021
|
|
Limit Position (Max Number of Turns)
|
|
3
|
1425
|
November 24, 2021
|
|
C、Odirve CAN Communication problems
|
|
2
|
782
|
November 23, 2021
|
|
Newbie to ODrives: Trying to set up my ODrive for Autonomous control as well as Manual Control
|
|
1
|
787
|
November 23, 2021
|
|
Cool but would it work on a Corexy?
|
|
85
|
17885
|
November 20, 2021
|
|
Motor not calibrating (Inductance and current out of range)
|
|
3
|
2755
|
November 17, 2021
|
|
How to stop ODrive when the microcontroller shuts down
|
|
2
|
949
|
November 15, 2021
|