|
Every time need calibration of ODrive when I reboot or restart the Odrive
|
|
5
|
2194
|
September 15, 2021
|
|
Odrive not working anymore (5V regulator issue)
|
|
2
|
896
|
September 15, 2021
|
|
Odrive does not execute position or velocity commands
|
|
4
|
1461
|
September 14, 2021
|
|
No connect, now a brick
|
|
5
|
1223
|
September 13, 2021
|
|
Motor closed loop cannot operate normally
|
|
10
|
824
|
September 13, 2021
|
|
A wired problem ,one odrive with one motor working smoothly,but with two is not
|
|
6
|
1333
|
September 13, 2021
|
|
Odrive firmware is completely erased
|
|
6
|
2007
|
September 12, 2021
|
|
Have problem need to reinstall firmware
|
|
3
|
524
|
September 12, 2021
|
|
Odrv0.axis0.config.enable_sensorless_mode Does not Exist?
|
|
10
|
1922
|
September 11, 2021
|
|
Does oDrive suite for low power motor, like < 50w or less?
|
|
6
|
769
|
September 10, 2021
|
|
Calibration procedure not completing
|
|
6
|
2604
|
September 10, 2021
|
|
Shipping Time Europe
|
|
1
|
504
|
September 10, 2021
|
|
0.5.3. firmware with 0.5.2. backup-config
|
|
1
|
705
|
September 8, 2021
|
|
ODrive 24V board usage with battery
|
|
1
|
649
|
September 8, 2021
|
|
Difficulty upgrading firmware
|
|
1
|
1948
|
September 8, 2021
|
|
Odrive 3.6 case
|
|
2
|
1888
|
September 6, 2021
|
|
Can Message : 0x001 "ODrive Heartbeat Message"
|
|
0
|
641
|
September 6, 2021
|
|
Odrivetool doesn't find odrive on MacBook Pro
|
|
14
|
1033
|
September 6, 2021
|
|
Can bus drivers - firmware -
|
|
0
|
430
|
September 6, 2021
|
|
No backend error
|
|
4
|
5457
|
September 4, 2021
|
|
Flush the velocity PID loop to prevent unwanted yaw correction
|
|
1
|
468
|
September 4, 2021
|
|
Firmware 0.5.2 Release Thread
|
|
62
|
10360
|
September 2, 2021
|
|
Firmware upgrade to 0.5.2usb disappear, brush 0.5.1 firmware completely normal, solve the problem
|
|
17
|
1925
|
September 1, 2021
|
|
Cannot flash Odrive3.5 with StLINK V2-1
|
|
9
|
4717
|
August 31, 2021
|
|
Unkown Error 0x00000004
|
|
5
|
1811
|
August 31, 2021
|
|
RuntimeError: An error occured. Device Status: (11, 10, 0, 0)
|
|
4
|
616
|
August 31, 2021
|
|
Hall efect sensor does not work
|
|
2
|
715
|
August 30, 2021
|
|
Input_pos goes to zero when entering to closed loop control
|
|
1
|
595
|
August 29, 2021
|
|
Compatibility with a stepper motor
|
|
4
|
1963
|
August 27, 2021
|
|
USB over-current error
|
|
1
|
1521
|
August 27, 2021
|