Support

ODrive Micro Support ODrive v3 Support If you need help with your ODrive v3 this is the place to get it. ODrive Pro Support If you need help with your ODrive Pro this is the place to get it. ODrive S1 Support If you need help with your ODrive S1this is the place to get it.

Topic	Replies	Views	Activity
About the Support category Support	0	2395	April 7, 2017
LDO for ODrive S1 ODrive S1 Support	3	37	February 14, 2026
Half revolution during ODrive calibration, but spins fast from Dashboard ODrive S1 Support	0	28	February 13, 2026
Odrive Pro CAN Trouble when connecting to BigTreeTech Manta M8P ODrive Pro Support	2	54	February 12, 2026
Rough running skateboard motor ODrive S1 Support	15	699	February 10, 2026
buzzing whenever motor is enabled (ODrive S1 + M8325s motor kit) ODrive S1 Support	5	123	February 5, 2026
Motor_thermistor.temperature always NaN despite valid ADC on GPIO1 (fw 0.6.11) ODrive Micro Support	1	66	February 3, 2026
Low speed velocity ripple (0.16 r/s) on ODrive v3.6 with 10,000 CPR encoder - Tuning help needed ODrive v3 Support	0	92	January 28, 2026
BLDC torque controlled with speed limits ODrive Micro Support	9	204	January 26, 2026
Odrive 3.6 - where to find old ODriveArduino libraries? ODrive v3 Support	1	106	January 26, 2026
odesc 4.2 does not connect with pc Support	2	140	January 25, 2026
Inability to home motor ODrive S1 Support	1	113	January 25, 2026
ODrive S1 & Flat bldc motor \| INVALID_MOTOR_TYPE ODrive S1 Support	3	142	January 23, 2026
Odrive S1 bricked after update ODrive S1 Support	6	270	January 20, 2026
AXIS_ERROR_MIN_ENDSTOP_PRESSED prevents startup Support	5	486	January 18, 2026
Odrive UART communication failure[Fixed But ...] ODrive v3 Support	9	1345	January 12, 2026
Gimbal Motor tuning struggles with no errors ODrive S1 Support	10	383	January 9, 2026
Configuration of ODrive not saved after reboot ODrive S1 Support	3	214	January 9, 2026
Programmatic getattr() and setattr() use Support	3	150	January 6, 2026
CNC controller and Odrive ODrive Pro Support	7	942	January 6, 2026
Built-in encoder in Odrive micro ODrive Micro Support	2	168	January 4, 2026
ENCODER_OFFSET_CALIBRATION fails with POLE_PAIR_CPR_MISMATCH when encoder is geared relative to motor ODrive S1 Support	1	203	January 2, 2026
Calibration fails with gimbal motor ODrive Micro Support	3	246	December 30, 2025
Odrive Micro Regen Current - Help ODrive Micro Support	3	192	December 29, 2025
How to connect CAN-gnd? Support	3	229	December 23, 2025
S1 is not axeptated by GUI ODrive S1 Support	63	3210	December 23, 2025
Adding custom endpoint type to Odrive to send back multiple sensor values at once ODrive v3 Support	6	477	December 23, 2025
Regen clamp or brake resistor Support	4	1066	December 19, 2025
Read GPIO from Arduino code Support	2	185	December 16, 2025
Reverser rotation on motor Support	3	221	December 15, 2025