Motor for exoskeleton
|
|
1
|
1506
|
May 30, 2020
|
"SetParameter" Removed in Arduino Support File?
|
|
5
|
1002
|
May 30, 2020
|
Data from Liveplotter (pos_estimate) integrate into another process
|
|
2
|
734
|
May 30, 2020
|
Battery-percentage
|
|
1
|
582
|
May 30, 2020
|
Error_controller_failed
|
|
16
|
3748
|
May 29, 2020
|
Hoverboard motor in CLOSED_LOOP_CONTROL vibrates when overpowered
|
|
1
|
754
|
May 29, 2020
|
ERROR_CURRENT_UNSTABLE during AXIS_STATE_CLOSED_LOOP_CONTROL
|
|
2
|
1055
|
May 26, 2020
|
Odrivetool: too few arguments
|
|
2
|
884
|
May 25, 2020
|
UART speed in native mode
|
|
2
|
718
|
May 23, 2020
|
Encoder Connected to ODrive and Arduino
|
|
4
|
1137
|
May 20, 2020
|
Broken ODrive AGAIN
|
|
3
|
1186
|
May 19, 2020
|
Would it be possible to make a high voltage relatively cheap Odrive for Induction AC motors?
|
|
2
|
1357
|
May 19, 2020
|
Break resistor, Shunt regulator, low side mosfet
|
|
2
|
814
|
May 18, 2020
|
Urgent - Index pulse counter
|
|
1
|
651
|
May 18, 2020
|
Odrive controller with Li-ion supply (maximum supply voltage)
|
|
0
|
615
|
May 17, 2020
|
DC motor on AUX
|
|
0
|
742
|
May 16, 2020
|
[ASCII] [.NET] Some questions
|
|
1
|
633
|
May 15, 2020
|
Current and voltage limits
|
|
0
|
1492
|
May 13, 2020
|
NO error and save the configuration failed
|
|
0
|
600
|
May 12, 2020
|
Just Ordered Odrive HV and building a custom higher voltage one
|
|
0
|
694
|
May 8, 2020
|
Odrive hanging Pi3
|
|
0
|
528
|
May 8, 2020
|
Recommandation for a male connector to plug in J3/J4 female connector
|
|
0
|
560
|
May 8, 2020
|
4Poles 1300kv stopping when high speeds are required
|
|
18
|
2941
|
May 7, 2020
|
Introductions | New to the Forum
|
|
14
|
5519
|
May 7, 2020
|
Sensorless Motor Question
|
|
0
|
553
|
May 5, 2020
|
Get_inverter_temp through ASCII no response
|
|
4
|
734
|
May 4, 2020
|
Okay to Sell your ODrive here?
|
|
3
|
965
|
May 4, 2020
|
Power Supply O-drive
|
|
3
|
2519
|
May 3, 2020
|
Broken ODrive fix?
|
|
1
|
906
|
May 3, 2020
|
Linear motor (as an on/off actuator)
|
|
3
|
829
|
May 3, 2020
|