ODrive Community

Topic	Replies	Views	Activity
Come chat with us! In order to provide a direct way for people to chat, and better support things like security, moderation and fancy things like voice and video chat, desktop sharing, etc, I have established a Discord server. You can joi…	9	18564	June 14, 2022
Low frequency bus voltage & current ripple	3	26	December 11, 2025
S1 is not axeptated by GUI ODrive S1 Support	52	2474	December 11, 2025
ODrive S1 CAN DIP switch for 120Ohm resistor ODrive S1 Support	3	37	December 11, 2025
Increase in vel_gain issue ODrive Pro Support	9	93	December 8, 2025
Odrive Micro Loss of Commutation in Torque Mode with No Magnet Slippage	1	63	December 8, 2025
ODrive S1 Torque Control Performace Shows Asymmetreic Behaviour/Error Code 8 (missing encoder estimate error) ODrive S1 Support	11	493	December 5, 2025
Anti-cogging and Joint Limits	4	92	December 4, 2025
Pre-calibrated Motor + Encoder Issue on ODrive v3.6 (0.5.6) with Hoverboard Motor & AS5047P	1	76	December 4, 2025
Unable to upgrade ODrive 3.6-56V from 0.5.1 to 0.5.6 with odrivetool ODrive v3 Support	1	90	December 3, 2025
Encoder output from Odrive Pro	8	656	December 1, 2025
Where to find motor with low cogging torque (skewed slots/magnets)	5	187	November 27, 2025
Communication Issue with ODrive S1 Nodes via CAN Interface Beyond Certain Node IDs ODrive S1 Support	13	4347	November 27, 2025
Odrive Pro Max rated Fan current ODrive Pro Support	2	128	November 25, 2025
Parallel working of odrives on same motor	3	134	November 24, 2025
A 2 axis Gimbal-with different size motor	1	106	November 21, 2025
Moving to a position set point using UART Support	5	162	November 21, 2025
Adding custom endpoint type to Odrive to send back multiple sensor values at once ODrive v3 Support	1	165	November 20, 2025
CAN ODrive Wire Check ODrive S1 Support	1	138	November 20, 2025
ODrive S1 Ground Loops CAN - Don't Understand ODrive S1 Support	1	159	November 20, 2025
ESP32 and CAN or not? Support	2	164	November 20, 2025
Too little torque at max current under torque control mode ODrive Pro Support	7	272	November 20, 2025
USB Connection Error with ODrive Micro ODrive Micro Support	0	132	November 19, 2025
Motor velocity actively limited for unknown reason ODrive S1 Support	3	169	November 18, 2025
How does Feedforward Position Work?	1	136	November 18, 2025
How to use ODrive Pro with AksIM-4 encoder with the SPI EncoLink protocol ODrive Pro Support	1	138	November 16, 2025
Dead-zone for PWM velocity control?	10	2546	November 14, 2025
ODrive Micro CAN is not working ODrive Micro Support	4	149	November 14, 2025
Communication between oDrive micro and STM32 ODrive Micro Support	3	180	November 11, 2025
ODrive 1st Time CAN Control ODrive S1 Support	1	174	November 10, 2025

Come chat with us!

In order to provide a direct way for people to chat, and better support things like security, moderation and fancy things like voice and video chat, desktop sharing, etc, I have established a Discord server. You can joi…