|
Can't setup sensorless
|
|
0
|
821
|
December 30, 2021
|
|
How to complie the odrive's firmware
|
|
3
|
1096
|
December 30, 2021
|
|
ASCII Protocol wont move motors
|
|
6
|
683
|
December 30, 2021
|
|
Dust + Encoder = Any experience?
|
|
1
|
880
|
December 30, 2021
|
|
Hooking up the FFboard with odrive via CAN (post-hooking up)
|
|
3
|
1613
|
December 30, 2021
|
|
Odrive shows 0.0 for motor phase_inductance and phase_resistance
|
|
0
|
805
|
December 28, 2021
|
|
36V on 24V Odrive board
|
|
2
|
1131
|
December 28, 2021
|
|
56V ODesc Current Limit
|
|
1
|
723
|
December 27, 2021
|
|
Max. Voltage D5065
|
|
2
|
1097
|
December 25, 2021
|
|
ODrive Brake Resistor Config/Enable Error
|
|
23
|
3845
|
December 24, 2021
|
|
Phase inductance out of range after changing shunts
|
|
2
|
976
|
December 23, 2021
|
|
DC_BUS_UNDER_VOLTAGE during position control
|
|
2
|
1635
|
December 22, 2021
|
|
Motor not turning after closed loop state
|
|
3
|
921
|
December 22, 2021
|
|
DC Bus Under Voltage Error
|
|
4
|
3982
|
December 21, 2021
|
|
Motor only turn onece ,ang nexy not turning when after closed loop state
|
|
13
|
1062
|
December 21, 2021
|
|
Is it possible to control DC motor from Odrive tool?
|
|
3
|
1551
|
December 21, 2021
|
|
ODrive USB connections
|
|
4
|
678
|
December 21, 2021
|
|
Generic_Timer_method
|
|
1
|
626
|
December 21, 2021
|
|
Odd v3.6 56 Volts
|
|
1
|
631
|
December 21, 2021
|
|
8192 CPR Encoder - shorter cable
|
|
3
|
916
|
December 20, 2021
|
|
Using Odrive on BLDC Micromotor with Internal Hall Sensor
|
|
4
|
1320
|
December 20, 2021
|
|
Using trajectory mode
|
|
2
|
900
|
December 18, 2021
|
|
Arduino stops receiving GetPosition data after a few seconds
|
|
11
|
1417
|
December 17, 2021
|
|
Tuning a D6374 to the limits
|
|
3
|
887
|
December 15, 2021
|
|
Mechanical Brake control through arduino
|
|
3
|
1308
|
December 15, 2021
|
|
Secondary absolute position measurement at the other end of a reduction stage
|
|
2
|
674
|
December 14, 2021
|
|
Control 24V BLDC MOTOR (Brake, Encoder)
|
|
16
|
3344
|
December 13, 2021
|
|
[LEGACY_PROTOCOL] previous endpoint operation still not sent
|
|
1
|
1417
|
December 12, 2021
|
|
Is my ODrive Fried?
|
|
1
|
681
|
December 11, 2021
|
|
I want to get encoder pulses in Arduino from odrive.How can I get that?
|
|
1
|
770
|
December 11, 2021
|