|
V3.5 Only one interface in RUN mode
|
|
0
|
717
|
August 15, 2019
|
|
I can't go any further
|
|
2
|
1037
|
August 14, 2019
|
|
ERROR BRAKE CURRENT OUT OF RANGE when trying to sustain 7200 RPM
|
|
9
|
1424
|
August 14, 2019
|
|
No usb device showing
|
|
15
|
9013
|
August 14, 2019
|
|
Why no one helps me? not even the support
|
|
2
|
1239
|
August 14, 2019
|
|
Question from a total noob
|
|
6
|
990
|
August 13, 2019
|
|
Vel_setpoint in sensorless mode
|
|
1
|
882
|
August 13, 2019
|
|
Viability of changing firmware to run my code
|
|
0
|
532
|
August 11, 2019
|
|
Adding hall sensors to a motor
|
|
2
|
1673
|
August 11, 2019
|
|
OdriveArduinoTest.ino Won't Compile
|
|
0
|
522
|
August 10, 2019
|
|
Hardware limits
|
|
1
|
1800
|
August 7, 2019
|
|
Limitation of Current and Current settings
|
|
0
|
522
|
August 5, 2019
|
|
Motor stops moving
|
|
0
|
733
|
August 5, 2019
|
|
Tiger Motor U10 plus tuning
|
|
0
|
823
|
August 1, 2019
|
|
Native Mode over UART (GPIO 1 and 2)
|
|
1
|
957
|
August 3, 2019
|
|
Linux Odrive USB protocol problem
|
|
5
|
1445
|
August 2, 2019
|
|
Problems Encoder Calibration, Motor does not move
|
|
0
|
817
|
August 2, 2019
|
|
Problem with calibration odrive
|
|
0
|
488
|
August 2, 2019
|
|
The controller is not flashing!
|
|
1
|
943
|
August 1, 2019
|
|
Overspeed error tuning help
|
|
0
|
758
|
August 1, 2019
|
|
CNC - Milling - Request for Advice
|
|
15
|
5172
|
August 1, 2019
|
|
Newbie Project: Figuring out motor
|
|
2
|
679
|
August 1, 2019
|
|
Is the metal shaft of the D6374 150 KV interchangeable?
|
|
0
|
487
|
July 31, 2019
|
|
Kickin it down a notch (ODrive Jr.?)
|
|
0
|
811
|
July 31, 2019
|
|
Encoder on M1 not working
|
|
3
|
1050
|
July 30, 2019
|
|
M1 Encoder pins not working properly - FIXED
|
|
1
|
1009
|
July 30, 2019
|
|
Odrive and Touchdesigner?
|
|
6
|
1501
|
July 29, 2019
|
|
ODrive and Arduino Connection
|
|
2
|
3024
|
July 28, 2019
|
|
Which Encoders to choose
|
|
8
|
20023
|
July 28, 2019
|
|
Need more wiring and circuit info on V3.6
|
|
7
|
3102
|
July 26, 2019
|