|
Graphs and send commands at the same time
|
|
3
|
1540
|
July 5, 2021
|
|
3-phase stepper motors with ODrive?
|
|
1
|
1202
|
July 5, 2021
|
|
Any attempt to connect with ODrive via USB won't work
|
|
13
|
6427
|
July 3, 2021
|
|
Tuning a hoverboard type hub motor with external encoder
|
|
0
|
2313
|
July 2, 2021
|
|
Closed loop control: Axis Error 512
|
|
15
|
4268
|
July 2, 2021
|
|
Some questions about ERROR_SPI_COM_FAIL during two motor working!
|
|
2
|
946
|
July 1, 2021
|
|
ODrive board 3.6 not showing up as com port [SOLVED]
|
|
3
|
3401
|
July 1, 2021
|
|
Oh no odrv0 disappeared
|
|
10
|
5337
|
June 30, 2021
|
|
Unknown axis error 0x00000200
|
|
5
|
2213
|
June 29, 2021
|
|
Connection Issue
|
|
4
|
1391
|
June 29, 2021
|
|
The motor error of "ERROR_DRV_FAULT"
|
|
16
|
6241
|
June 29, 2021
|
|
V0.5.2 Release Upgrade Woes
|
|
6
|
1141
|
June 28, 2021
|
|
Firmware Update Problems
|
|
9
|
4601
|
June 28, 2021
|
|
USB comms fail after failed upgrade
|
|
3
|
1331
|
June 28, 2021
|
|
Current measurement timeout
|
|
1
|
1155
|
June 28, 2021
|
|
Braking Question
|
|
2
|
896
|
June 27, 2021
|
|
Building a DOF6 with the Odrive parts?
|
|
1
|
765
|
June 27, 2021
|
|
Odrive Voltage Rating
|
|
1
|
913
|
June 26, 2021
|
|
Encoder jitter during calibration (Causes failure), but reads fine when backdriven by hand,
|
|
3
|
1078
|
June 26, 2021
|
|
Odrive + openpnp?
|
|
9
|
2784
|
June 26, 2021
|
|
Closed-loop, but motor gets "soft" for long position setpoints, unable to reach setpoint while no error
|
|
10
|
1025
|
June 25, 2021
|
|
Manual Firmware Installation
|
|
3
|
2858
|
June 22, 2021
|
|
Raspbian python 3.9.2 installed, but odrivetool tries to run python 3.7
|
|
1
|
1742
|
June 22, 2021
|
|
Maximum update rate O-drive
|
|
5
|
2024
|
June 21, 2021
|
|
Issues with rebooted ODrive with or without precalibration
|
|
3
|
1158
|
June 21, 2021
|
|
The motor only runs in one direction with calibration and doesn't respond to any commands afterwards
|
|
8
|
2240
|
June 21, 2021
|
|
UART parameters calibration
|
|
8
|
1738
|
June 19, 2021
|
|
Liveplotter on OSX - No Anaconda
|
|
4
|
1417
|
June 19, 2021
|
|
Is there a parameter to control the time taken to reach from one point to another?
|
|
4
|
837
|
June 19, 2021
|
|
Momentum Wheel Torque Control
|
|
5
|
1933
|
June 19, 2021
|