|
Motor is slowing down over time
|
|
3
|
762
|
March 30, 2020
|
|
Odrive 3.5 firmware upload
|
|
9
|
1504
|
March 29, 2020
|
|
Sensored Stall Detection
|
|
1
|
963
|
March 29, 2020
|
|
Trouble getting started, 1500w 48v motor
|
|
11
|
2038
|
March 28, 2020
|
|
Encoder with Multiple Index Pulses
|
|
4
|
1128
|
March 28, 2020
|
|
1000W resistor?
|
|
6
|
908
|
March 28, 2020
|
|
Hoverboard motors switch from Hall to Encoders, now errors
|
|
1
|
826
|
March 28, 2020
|
|
Need coding help modifying ASCII protocol code
|
|
1
|
955
|
March 26, 2020
|
|
Encoder cable shielding
|
|
6
|
5687
|
March 25, 2020
|
|
Odrive v3.6 not being recognized on Windows, Linux, R-Pi4 ANYTHING
|
|
5
|
2125
|
March 25, 2020
|
|
Legal\illegal hall states?
|
|
1
|
624
|
March 23, 2020
|
|
Development board pre-installed
|
|
4
|
869
|
March 23, 2020
|
|
Closed Loop violent vibrations
|
|
4
|
1461
|
March 20, 2020
|
|
Leather sewing machine, hoverboard hub motor. Low speed high torque?
|
|
2
|
1433
|
March 20, 2020
|
|
Odrive v3.6 current surge affecting USB?
|
|
1
|
747
|
March 20, 2020
|
|
Set the first position
|
|
2
|
1120
|
March 20, 2020
|
|
Velocity using step/dir possible?
|
|
6
|
1055
|
March 17, 2020
|
|
use stm32 with odrive
|
|
1
|
1100
|
March 17, 2020
|
|
Error_motor_disarmed & error_control_deadline_missed
|
|
3
|
3053
|
March 17, 2020
|
|
Stall Torque and Bus Voltage
|
|
2
|
1369
|
March 17, 2020
|
|
Motor move to position issue
|
|
9
|
2350
|
March 17, 2020
|
|
Continuous current limit
|
|
1
|
714
|
March 17, 2020
|
|
Motors getting really hot during motor and encoder offset calibration
|
|
1
|
1112
|
March 17, 2020
|
|
Choppy operation with D5065 motor
|
|
1
|
792
|
March 17, 2020
|
|
Missing controller command move_to_pos
|
|
2
|
1317
|
March 17, 2020
|
|
ODrive Broken after Soldering
|
|
1
|
737
|
March 17, 2020
|
|
Odrive Controller powers down motor after short amounts of use
|
|
1
|
522
|
March 17, 2020
|
|
Problem with AXIS_STATE_MOTOR_CALIBRATION and Hoverbord Motor
|
|
2
|
2622
|
March 16, 2020
|
|
Motor recommendations for ~28-32mm diameter?
|
|
0
|
522
|
March 16, 2020
|
|
Using a lower voltage motor with a higher voltage supply
|
|
1
|
872
|
March 16, 2020
|