|
Help encoder polepair mismatch error troubelshooting
|
|
0
|
825
|
September 1, 2022
|
|
TMotor R60 kv115
|
|
4
|
1112
|
August 29, 2022
|
|
The motor can't reach half of its maximum speed
|
|
6
|
1687
|
August 27, 2022
|
|
What does an AUX Terminal on the Odrive is used for?
|
|
4
|
2906
|
August 21, 2022
|
|
Unexpected movement under CONTROL_MODE_TORQUE_CONTROL & input_torque=0
|
|
3
|
757
|
August 21, 2022
|
|
CAN Bus Not Responding
|
|
4
|
1487
|
August 20, 2022
|
|
Sensorless mode missing
|
|
2
|
805
|
August 20, 2022
|
|
Encoder attached to Motor via Gear Reduction
|
|
5
|
1228
|
August 20, 2022
|
|
Unstable operation in trap_traj mode
|
|
1
|
675
|
August 20, 2022
|
|
Make Error: Make not recognizing commands in makefile
|
|
6
|
6182
|
August 20, 2022
|
|
PWM frequency, Id current, liveplotter
|
|
1
|
1314
|
August 20, 2022
|
|
Could the ODrive version be the reason for trouble in my board?
|
|
1
|
742
|
August 19, 2022
|
|
Shunt resistor packaging, odrv3.6
|
|
2
|
771
|
August 17, 2022
|
|
An error occurs when VScode configures the odrive firmware development environment
|
|
4
|
777
|
August 16, 2022
|
|
Matching pole_pair gives error
|
|
4
|
892
|
August 15, 2022
|
|
EncoderError.ABS_SPI_COM_FAIL
|
|
3
|
1721
|
August 14, 2022
|
|
Errors connecting to ODrive
|
|
3
|
1028
|
August 10, 2022
|
|
Motor spins with the VEL_LIMIT, but does not respond to inputs
|
|
4
|
1224
|
August 10, 2022
|
|
Hall sensors - name ‘GPIO_MODE_DIGITAL’ is not defined
|
|
1
|
853
|
August 10, 2022
|
|
Where are the GPIO configs?
|
|
4
|
2641
|
August 10, 2022
|
|
Odrive suddenly loses complete configuration
|
|
10
|
1207
|
August 10, 2022
|
|
ODrive 3.6-56V can't connect to hoverboard motor
|
|
12
|
3110
|
August 10, 2022
|
|
Fw-0.5.1 Build problem
|
|
1
|
571
|
August 6, 2022
|
|
Odrivetool loss ENCODER_MODE_INCREMENTAL parameter
|
|
2
|
887
|
August 4, 2022
|
|
How to use AS5600 Encoder with O-drive
|
|
3
|
3954
|
August 4, 2022
|
|
Start-up support
|
|
5
|
838
|
August 4, 2022
|
|
Trap_traj input secrets?
|
|
2
|
1708
|
August 4, 2022
|
|
Motor doesn´t move in initial Calibration
|
|
2
|
1643
|
August 4, 2022
|
|
Realized motor current << current_lim setting
|
|
4
|
2262
|
August 4, 2022
|
|
Low torque during velocity control
|
|
0
|
682
|
August 2, 2022
|