|
Compatibility with a stepper motor
|
|
4
|
2156
|
August 27, 2021
|
|
USB over-current error
|
|
1
|
1643
|
August 27, 2021
|
|
Error on controller.input_vel = 0
|
|
13
|
2655
|
August 27, 2021
|
|
Bldc motor becomes weak over time
|
|
9
|
1297
|
August 27, 2021
|
|
Unable to detect Odrive
|
|
1
|
839
|
August 26, 2021
|
|
Contact odrive email/phone#
|
|
1
|
657
|
August 26, 2021
|
|
How can i clamp current_cmd to avoid current_limit_violation
|
|
1
|
800
|
August 25, 2021
|
|
Gpio mode problem
|
|
6
|
1587
|
August 24, 2021
|
|
Torque when using Arudino with Hoverboard motor
|
|
1
|
899
|
August 24, 2021
|
|
Firmware update failed, no device found now
|
|
1
|
711
|
August 23, 2021
|
|
Hoverboard motors calibrated fine but now error after turning once
|
|
4
|
1210
|
August 22, 2021
|
|
Implementation of sound feature
|
|
4
|
1355
|
August 22, 2021
|
|
Cannot set torque_constant on new odrive
|
|
1
|
990
|
August 22, 2021
|
|
Error using 2 motors: ERROR_MODULATION_IS_NAN
|
|
4
|
2304
|
August 21, 2021
|
|
Current control on sensorless mode
|
|
2
|
1197
|
August 18, 2021
|
|
Getting control loop values
|
|
1
|
545
|
August 17, 2021
|
|
Sensorless at high speed
|
|
4
|
1899
|
August 17, 2021
|
|
Failed to read serial_number using ASCII protocol
|
|
3
|
893
|
August 17, 2021
|
|
ODrive not powering on
|
|
2
|
603
|
August 17, 2021
|
|
Axis_error_motor_failed - FIXED
|
|
8
|
5748
|
August 16, 2021
|
|
What are the High-level source current and the Low-level sink current of GPIO?
|
|
0
|
543
|
August 16, 2021
|
|
Using UART with ODrive
|
|
0
|
1306
|
August 16, 2021
|
|
What are appropriate motor current_lim values?
|
|
9
|
2459
|
August 15, 2021
|
|
Only one spi master use,
|
|
3
|
729
|
August 15, 2021
|
|
DFU Flashing Error
|
|
5
|
3041
|
August 15, 2021
|
|
Hoverboard Motor | Speed Variation
|
|
0
|
790
|
August 14, 2021
|
|
DC_BUS_OVER_REGEN_CURRENT (Error)
|
|
1
|
3787
|
August 14, 2021
|
|
I am getting an unknown error code on motor calibration
|
|
1
|
779
|
August 13, 2021
|
|
Endstop ghost-triggered by call to encoder.pos_estimate
|
|
3
|
594
|
August 12, 2021
|
|
Problem with save_configuration() using python
|
|
4
|
2484
|
August 12, 2021
|